Skip to main content

Plumber services · Delhi NCR

Tap Installation in Delhi NCR

Most taps that drip within a month of being fitted were over-tightened onto a worn wall socket, not badly made. We check the threads and the concealed elbow first, replace the seal properly, and torque to the point where it seals rather than where it cracks the chrome.

Starts from
₹150
Typical duration
20–90 min
Guarantee
30 days

Common problems

What usually goes wrong — and what we actually do about it

The three faults we are called out for most often under tap installation, with the cause behind each.

  • A new tap drips from the base, not the spout

    Usually because: Failed seal at the wall thread, often from over-tightening or reused tape.

    What we do: Fixture is removed, thread cleaned back, and re-sealed correctly.

  • The tap turns but water barely comes out

    Usually because: A clogged aerator — NCR hard water scales them quickly — or a partly closed angle valve.

    What we do: Aerator is cleaned or replaced and the supply valve checked through its full travel.

  • The mixer gives hot on the cold side

    Usually because: Hot and cold inlets crossed at installation, or a failed cartridge.

    What we do: Inlets are corrected at the wall, or the cartridge replaced.

What the booking includes

  • Removing the existing tap, mixer or faucet
  • Checking and cleaning the wall socket or concealed elbow threads
  • Fresh sealing tape or thread compound on every joint
  • Fitting and aligning the new fixture square to the wall
  • Running each outlet and checking for weep at the base

What it does not cover

Listed so nothing appears on the bill that was not discussed up front.

  • The tap, mixer or faucet itself
  • Replacing a damaged concealed elbow inside the wall (quoted separately)
  • Tile cutting or repair

Pricing

Tap Installation price list — Delhi NCR

Indicative ranges for a normal job. City-specific figures are on each city page below.

JobIndicative price
Bib cock / pillar tap installation₹150 – ₹300per tap
Wall-mixer or diverter installation₹350 – ₹700per unit
Health faucet / jet spray fitting₹200 – ₹450
Concealed diverter servicing₹600 – ₹1,500
Angle valve replacement₹200 – ₹450per valve

These are indicative ranges for typical jobs, not quotes. You see the actual price for your job before you confirm the booking. A visiting charge of ₹99₹149 applies where an inspection is needed, and it is adjusted against your final bill. Materials are billed separately and itemised on your digital invoice.

Before we arrive

A few things that make the visit faster

  • Keep the new fixture and its washers, flanges and adaptors together in one place
  • Batch all the taps you want changed into a single visit
  • Know where the flat's main stopcock is in case a valve is seized

Also searched as

Looking for tap installation? People across Delhi NCR also ask for this as nal lagwana, tap fitting, mixer installation or jet spray fitting. You can book in whichever words are natural to you — our support team works in Hindi and English, and so do the professionals who take the job.

FAQs

Tap Installation — common questions

Do you bring the tap, or should I buy it?

You buy it, so the brand, finish and manufacturer warranty are yours. Bring the full box — the flange, washers and adaptor in it are usually what the fitting needs, and generic substitutes are the most common cause of a base leak later.

My tap threads are damaged inside the wall. What then?

The concealed elbow behind the tile has stripped, which no amount of sealing tape fixes. It needs the tile opened and the elbow replaced — a bigger job than a tap change, and one we will quote separately rather than tape over. Any plumber who says they can seal a stripped socket permanently is buying you a few weeks.

Book tap installation with a verified plumber

Upfront pricing from ₹150, same-day slots across Delhi NCR, and a 30-day guarantee on eligible work.